How To Remove Embroidery Patch?

How To Remove Embroidery Patch?

how to remove embroidery patches

The beauty and uniqueness of custom embroidered patches often add a distinctive touch to clothing. However, in certain situations, there arises a need to remove them. Whether it’s to replace with new patches, adjust the garment design, or for other personal reasons, the correct and effective embroidery removal methods are crucial.

So this article will share two main ways of how to remove embroidery patch.

There are two main ways “how to remove embroidered patches”. One is removing sewn-on patches, the iron-on patches, and self-adhesive patches.

Let’s begin step by step:

How To Remove a Sewn-On Patch?

  1. Prepare Tools: Firstly, make sure you have the necessary tools such as scissors, sewing needle, cleaner, etc.

  2. Identify Patch Location: Confirm the location where the patch is sewn and mark it on the inside of the garment for easier handling.

  3. Cut Thread Ends: Carefully cut the ends of the sewing thread with scissors, ensuring not to damage the garment.

  4. Gradual Disassembly: Slowly and carefully disassemble the sewn threads, avoiding tearing the fabric. If encountering resistance, use a sewing needle to gently loosen the threads.

  5. Clear Residual Thread Ends: After removing the patch, inspect and clear any remaining sewing thread ends on the fabric to ensure a smooth surface.

  6. Clean Residual Traces: If necessary, use an appropriate cleanser or washing method to address any residual glue or traces.

How To Remove A Iron On Patch?

Tools you will need:

  1. Iron: Make sure it can be adjusted to an appropriate temperature to soften the adhesive.
  2. Small knife or scissors: For carefully lifting the edges of the iron-on patch.
  3. Fabric or thin cloth: To cover the patch, preventing direct contact with the iron and protecting the garment.
  4. Cleaning agent: Choose an appropriate cleaning agent for removing any residual adhesive or traces.
  5. Nail or edge tool: For precise attempts at lifting the edges of the iron-on patch, especially after heating.

Steps:

  1. Heat the surface: Preheat the iron, ensuring it reaches the right temperature.
  2. Protect with covering: Place a thin cloth over the iron-on patch to avoid direct contact with the iron.
  3. Iron-on heating: Gently place the iron on the covered patch and continue heating.
  4. Gradual peeling: After heating, use a small knife or nail to gently lift the edges of the patch, proceeding cautiously to avoid damaging the garment.
  5. Clear residue: After removing the iron-on patch, use a cleaning agent to clear any remaining adhesive.
  6. Iron the surface: Finally, use the iron to gently flatten the garment’s surface, ensuring no noticeable marks or wrinkles.

How to Remove A Self-Adhesive Patch From Clothing?

  1. Prepare Tools: Ensure you have scissors, fabric or a thin cloth, hairdryer or heat gun, and any necessary cleaning agents.

  2. Identify Location: Locate the adhesive patch on the clothing and mark it on the inside for easier handling.

  3. Heat the Patch: Gently heat the patch using a hairdryer or heat gun. This helps soften the adhesive, making it easier to peel off.

  4. Carefully Peel: After heating, carefully use your nails or an edge tool to start peeling from one corner of the patch. Ensure you avoid pulling or damaging the fabric.

  5. Clear Residual Adhesive: After removing the patch, inspect and clear any remaining adhesive on the clothing. You can use a cleaning agent or washing method.

  6. Smooth the Surface: Finally, gently use your fingers or an iron to smooth the clothing’s surface, ensuring there are no residual marks or wrinkles.

In conclusion, this article shows three ways how to remove embroidery patches with 3 different backings – sewn on, iron-on, and self-adhesive.

If you have a better idea, please leave a comment below: )

More Posts

Send Us A Message

Leave a Reply

Your email address will not be published. Required fields are marked *

Embroidery Patch Backing Type-patch backing